1-slide track at top to 'tv' (all the way right) 2-hold 'mute' & 'select' simultaniously until light blinks twice(approx 5 secs) 3-type the code 11758 test by hitting volume up or down, make sure you follow these instructions all while pointing remote at tv sensor
Some older receivers don't have newer brand names listed. You can find codes on www.directv.com/remotecodes or ask us as you did. I have a Vizio and 10864 works perfectly. The others are 11758, 10885, 11499, and 11756. All the best!!
I know the directv system up and down. I can give you an answer to anything. I've been a technician for directv for over 4 years. Certified in every field.
With the tv code that give you partial control programmed, try the following: 1. tv 2. press and hold MUTE & SELECT for two blinks 3. enter 993 4. press SELECT If you still don't have vol control, I suggest searching tv codes by vol command, like so: 1. tv 2. press and hold MUTE & SELECT for two blinks 3. enter 991, wait for two blinks 4. enter 1 5. press VOL UP 6. keep pressing and releasing CH UP, if and when the tv vol changes 7. press SELECT to lock in code.
being in crg (customer retention group/save team), i am the last person you will ever need to speak with to resolve you concern.
Remote Control Programming Remote Control Code Lookup This handy online tool gives you the code you need to set up your remote to control the devices connected to your TV. Get your code
How to program your DIRECTV remote control:
Press MENU on remote. Select "Parental, Favs and Setup". Select "System Setup". Select "Remote". Select "Program Remote". While aiming remote at device, follow onscreen instructions to program remote to TV, DVD, or other device.
How to program the white DIRECTV remote to your TV
Look up the control codes for your DIRECTV remote control. Make sure your TV is turned on. Slide the mode switch at top of remote to "TV". Press and hold the MUTE button. This is located above the number 1 button. While still holding down MUTE, press and hold the SELECT button until the green light at the top of the remote flashes twice. Enter the first TV code you have. The green light on remote should flash twice. Aim remote at TV and press PWR button once. The TV should power off. Once the TV is able to power off/on and control the volume, slide the mode switch at the top of the remote back to the left (DIRECTV). Your remote is now programmed. If the TV does not power off, repeat steps 4, 5, 6, and 7, using the next code for your TV brand.
If remote control fails to program using all available codes, try scanning for the code.
How to scan for TV codes on your DIRECTV remote
Make sure your TV is turned on. Slide the mode switch at top of remote to "TV". Press and hold the MUTE button. This is located above the number 1 button. While still holding down MUTE, press and hold the SELECT button until green light at the top of the remote flashes twice. Then enter 9911, the green light on remote should flash twice. Point remote at TV and press CHANNEL UP button. Tap the CHANNEL UP button repeatedly until the TV powers off. When the TV powers off, press and release the SELECT button. Note: If the green light flashes three times before TV responds, then all codes have been cycled through. Our remote controls are guaranteed to program to your DIRECTV receiver, however your TV may not be compatible with our remote control.
You can find more help in the Remote Controls section of our Technical Forums at forums.directv.com. You can also use our Interactive User Guide to learn the ins and outs of your remote control.
I can Help; I've been trained by DirecTV. I have worked as a Technical Support Supervisor for DirecTV for over 5 years
Setup Instructions 1.Set the "Mode Switch" to TV. 2.Press and hold the "Mute" button and the "Select" button until the visible LED blinks twice. 3.Enter the 5 digit Code The following code is the most popular for your brand. 11758 11756 10864 10885 11499 You may still find a setup code that works for your device by stepping through the library codes in your remote. The following instructions will help you do this.
StepNSet 1.Set the "Mode Switch" to the desired mode such as TV for a Television. 2.Press and hold the "Mute" button and the "Select" button until the visible LED blinks twice. 3.Enter the code "991" followed by the "device number" 1 for Televisions 2 for "AUX 1" devices - VCRs or DVDs 3 for "AUX 2" devices - Audio 4. You can step through the setup codes for this mode by pressing the "Channel Up" key to go forward through the codes or pressing the "Channel Down" key to go back to the previous codes. 5. You can try out each code by pressing one or more function keys such as power, volume or digit keys. 6.When you've found the setup code that works for your device, press the "Select" key.